Published by the team at Cloverdale HVAC

A gas furnace in a home utility room in Montgomery, AL, with the blower running but no heat coming from it

Furnace Runs But No Heat? Here's What to Check

A furnace that runs but gives no heat is usually stopped at ignition, at the filter, or at the thermostat. Check those in order, and treat a gas smell as a leave-the-house moment.

  • ✓21-point audit in full
  • ✓Call direct, no forms to fill
  • ✓Serving Montgomery, Prattville & Wetumpka

Why does my furnace run but give no heat?

A furnace can run and still give no heat because the blower and the burners are separate jobs. The blower moves air, and the burners make the heat. When the thermostat calls for heat, the blower can start while the burners never light, so the air coming from the vents stays cold.

The most common causes are the thermostat setting, a clogged filter, a failed igniter, or a dirty flame sensor. Montgomery cold snaps drop to 14-18°F on the coldest nights, so a no-heat furnace in January is not a wait-and-see problem. Check the safe things first, and stop the moment a check points at gas or ignition.

  • Thermostat: Heat mode, setpoint above room temperature, fan on Auto.
  • Filter: a clogged filter chokes airflow and trips the limit switch.
  • Igniter: a cracked igniter means the burners never light.
  • Flame sensor: a dirty sensor drops the flame after it lights.
  • Our page on furnace repair in Montgomery covers the same causes on a repair visit.
A gas furnace blower running in a home utility room in Montgomery, AL, with no heat coming from the vents
A gas furnace blower running in a Montgomery, AL home: why does my furnace run but give no heat.

What should I check first: thermostat, filter, ignition?

Start at the thermostat. Set it to Heat, raise the setpoint a few degrees above the room temperature, and set the fan to Auto, not On. Fan On blows room-temperature air all the time, which feels like no heat even when the furnace works. If the display is blank or dim, replace the batteries.

Then check the furnace switch, usually mounted near the unit, and the breaker. Then hold the filter up to a light and replace it if you cannot see through it. Ignition is not a homeowner check: do not open the furnace to look at the igniter or the flame sensor. If the burners never light after those checks, call.

  • Thermostat: Heat mode, setpoint above room temperature, fan on Auto, fresh batteries.
  • Furnace switch: check it is On, and check the breaker once.
  • Filter: replace it if you cannot see light through it.
  • Blower door: make sure the access panel is fully closed, or the furnace will not start.
  • Ignition: not a homeowner check. If the burners never light, call.
A furnace igniter inside a gas furnace in a Montgomery, AL home
A furnace igniter in a Montgomery, AL home: what to check first.

What if I smell gas?

Leave the house at once. Do not switch lights on or off, do not light anything, and do not go back inside to look for the source. Call the gas utility or emergency services from outside. Spire, the gas utility in Montgomery, is reached at 800-292-4008.

The same rule covers a carbon monoxide alarm: leave the house and call from outside. A cracked heat exchanger can let carbon monoxide into the air, and it has no smell, so the alarm is the warning. The technician checks the gas connections and the heat exchanger only after the house is safe.

  • Leave the house at once if you smell gas, and call from outside.
  • Spire, the gas utility: 800-292-4008.
  • Do not switch lights on or off, and do not light anything.
  • Carbon monoxide alarm: leave the house and call from outside.
  • Gas and ignition work is technician-only, and it starts only after the house is safe.
A furnace gas safety check in a Montgomery, AL home, with the gas valve and connections visible
A furnace gas safety check in a Montgomery, AL home: what if I smell gas.

When should I stop and call?

Stop and call when you smell gas, when the carbon monoxide alarm sounds, when the burners never light, or when the furnace keeps cycling on and off. Stop too if you see soot around the furnace or the flue, or if the thermostat, filter, and switch checks change nothing.

Heat pump homes have a second pattern: a heat pump that blows cold air, or auxiliary heat that stays on. Our page on heat pump repair in Montgomery covers that side. Either way, call with the symptom in your own words, and the technician confirms timing on the call.

  • Gas smell or CO alarm: leave the house and call from outside.
  • Burners never light: the fault is in ignition, so call.
  • Furnace cycles on and off: switch it off and call.
  • Soot around the furnace or flue: switch it off and call.
  • Heat pump blowing cold air: see heat pump repair, and call with the symptom.
An HVAC technician talking with a homeowner about a furnace that runs but gives no heat in Montgomery, AL
An HVAC technician talking with a homeowner in Montgomery, AL: when to stop and call.

Your questions, answered

The most common causes are the thermostat setting, a clogged filter, a failed igniter, or a dirty flame sensor. The blower can run while the burners never light, so the air stays cold. Check the thermostat, the filter, and the furnace switch first. If the burners never light, stop and call. Ignition and gas parts are technician-only.

Start at the thermostat: Heat mode, a setpoint above room temperature, fan on Auto, and fresh batteries if it uses them. Then check the furnace switch and breaker, then hold the filter up to a light and replace it if you cannot see through it. Ignition is not a homeowner check. If the burners never light after those checks, call.

Leave the house at once, and call the gas utility or emergency services from outside. Do not switch lights on or off, do not light anything, and do not go back inside to look for the source. Spire, the gas utility in Montgomery, is reached at 800-292-4008. The technician checks the gas connections only after the house is safe.

Short cycling usually means the furnace is overheating and the limit switch is cutting it off, often because a clogged filter has choked the airflow. A dirty flame sensor can do the same thing, by dropping the flame after it lights. Replace a clogged filter first. If it keeps cycling, switch the system off and call.

Stop and call when you smell gas, when the carbon monoxide alarm sounds, when the burners never light, or when the furnace keeps cycling on and off. Stop too if you see soot around the furnace or the flue, or if the furnace switch and breaker checks change nothing. Gas and ignition work is technician-only.

A homeowner talking with an HVAC technician about a furnace with no heat in Montgomery, AL
A homeowner talking with a technician in Montgomery, AL: your questions, answered.

Still no heat? Call with what you checked

Call now

Checked the Thermostat, Filter, and Switch? Call With the Result

Tell the technician what you checked and what happened. That is enough to start the visit.

Call About No Heat

Plan ahead

Want the Full Safety Sequence?

Read our page about furnace repair in Montgomery, the same safe checks, the stop points, and what a technician checks on the visit.

A no-heat furnace on a cold-snap night is a safety problem first, and a comfort problem second.

  • Montgomery cold snaps drop to 14-18°F on the coldest nights, so no heat is not a wait-and-see problem.
  • The same visit process covers Prattville homes and Wetumpka homes too.
An HVAC technician talking with a homeowner about a furnace that runs but gives no heat in Montgomery, AL
An HVAC technician talking with a homeowner in Montgomery, AL: still no heat?

Find us

Find Cloverdale HVAC in Montgomery

Cloverdale HVAC 714 E Main St, Prattville, AL 36067.

Get Help NowServices